Raypak TWPH-8550EHT08 Crosswind V 8550 Electric Heat Pump Pool Heater 138K BTU

The Raypak TWPH-8550EHT08 Crosswind V® 8550 Electric Heat Pump Pool Heater is a high-capacity vertical-discharge heat pump designed for residential pool and spa heating. This standard Crosswind V model provides efficient electric heat pump performance with a compact footprint, modern cabinet design, digital controls, and service-friendly front access.

This model is commonly used for in-ground pools and pool/spa systems where a 208-230VAC electric heat pump is preferred over a gas heater. Always confirm pool size, electrical service, breaker size, water flow, equipment pad space, plumbing layout, local code, and heater sizing before ordering.

Product Features

• Genuine Raypak Crosswind V® electric heat pump pool heater
• Manufacturer model / SKU: TWPH-8550EHT08
• Crosswind V 8550 standard heat pump model
• 138,000 BTU/h class heating performance where specified
• Vertical discharge design with a smaller equipment pad footprint
• 208-230VAC, single-phase electrical service where specified
• Digital control with microprocessor
• Digital diagnostics for service and operation feedback
• Titanium heat exchanger for pool and spa water applications
• Standard 2" PVC water connections
• Integrated Wi-Fi and Raymote™ fleet monitoring capability where supported
• Variable speed pump control capability where installed and configured correctly
• Designed for low-noise operation

Product Details

Compatibility

• Residential pools and spas requiring a Raypak Crosswind V TWPH-8550EHT08 heat pump
• Pool systems with 208-230VAC single-phase electrical service available
• Equipment pads where a vertical-discharge heat pump is preferred
• Systems using 2" pool plumbing where installed according to Raypak requirements
• Applications where electric heat pump heating is preferred over natural gas or propane heating
• Installations where water flow, electrical service, breaker size, clearances, and local code requirements are met

Common Uses

• Heating residential swimming pools
• Heating attached spas when properly sized and plumbed
• Replacing a compatible Crosswind V 8550 heat pump
• Adding efficient electric heat pump heating to an existing equipment pad
• Applications where a vertical-discharge heat pump design helps reduce side-clearance limitations

Important Notes

• This item is the heat pump heater only.
• Electrical wiring, disconnect, breaker, conduit, bonding, plumbing fittings, unions, check valves, bypass plumbing where required, equipment pad, automation wiring, and installation materials are sold separately unless otherwise stated.
• This is an electric heat pump and is not a natural gas or propane heater.
• This is the standard TWPH-8550EHT08 model and is not the same as the EHC heat/cool model.
• Verify electrical service, amperage, breaker size, wire size, local code, and utility requirements before purchase or installation.
• Heat pump performance depends on air temperature, water temperature, humidity, wind exposure, plumbing design, flow rate, pool cover usage, and overall pool heat loss.
• Pool sizing should be confirmed by a qualified pool professional, especially for large pools, shaded pools, windy locations, attached spas, or extended-season heating.
• Improper water chemistry, low flow, scale, freeze damage, incorrect bypass settings, or restricted airflow can damage the heat pump.
• Installation and service should be performed by a qualified pool heat pump professional according to Raypak instructions and local electrical code.

Installation Notes

• Confirm model TWPH-8550EHT08, voltage, amperage, breaker size, plumbing requirements, and local code requirements before installation.
• Install the heat pump on a level, stable equipment pad with proper drainage and service access.
• Maintain required airflow clearances around the cabinet and vertical discharge area.
• Use proper 2" plumbing practices and confirm inlet/outlet orientation before startup.
• Confirm proper water flow before operating the unit.
• Install any required bypass plumbing according to the system design and Raypak guidance.
• Bond and wire the unit according to the installation manual and applicable electrical code.
• Do not block the air inlet or discharge area with walls, fences, plants, equipment, or covers.
• Set up Wi-Fi and Raymote™ features only after the unit has been safely installed and commissioned.
• Check for water leaks, proper flow, correct voltage, and correct heating operation during startup.
• Register the unit and keep installation records, serial number, and startup documentation for warranty and service reference.

Related Products

• Raypak TWPH-8550EHT08 Crosswind V 8550 Heat Pump Electric Pool Heater
• Raypak 018045 R404A AVIA® Natural Gas Heater
• Raypak 009223 P-R406A-EN-C #51 Digital Natural Gas Heater
• Raypak 009227 P-R406A-EP-C #57 Digital Propane Gas Heater
• Raypak 014941 P-R406A-EN-X #51 Digital Natural Gas Heater
• Raypak 006721F Pool Heater Drain Plug Kit

Maintenance Tips

• Maintain proper pool water chemistry to help protect the titanium heat exchanger and internal components.
• Keep pH, alkalinity, calcium hardness, and sanitizer within recommended ranges.
• Clean the pool filter regularly to maintain proper water flow through the heat pump.
• Keep leaves, debris, landscaping, and equipment away from the air inlet and vertical discharge area.
• Inspect the equipment pad for water leaks, vibration, blocked airflow, corrosion, or electrical issues.
• Keep Wi-Fi credentials and app access updated if using Raymote™ features.
• Winterize the heat pump properly in freeze-prone conditions.
• Have refrigerant circuit, electrical components, water flow, controls, and heat exchanger condition checked by a qualified heat pump technician during routine service.